Prepare Top Cisco 300-510 Exam Study Guide Practice Questions Edition
Go to 300-510 Questions - Try 300-510 dumps pdf
NEW QUESTION # 89
Refer to the exhibit.
After troubleshooting an OSPF adjacency issue, routers 1, 2, and 3 have formed OSPF neighbor relationships. Which statement about the configuration is true?
- A. Router 2 uses router 3 as the next hop for 192.168.0.0/24
- B. Router 2 receives a Type 5 LSAs from router 1 for its connected subnets
- C. Router 2 receives a Type 7 LSAs from router 3 for its connected subnets
- D. Router 2 uses router 1 as the next hop for 192.168.0.0/24
Answer: D
Explanation:
From IOS 15.1(2)S onwards, Cisco uses the OSPF path selection order is O > O IA > N1 > E1 > N2 > E2 https://www.cisco.com/c/en/us/support/docs/ip/open-shortest-path-first-ospf/212608-ospf-external-path-selection-external-t.html
NEW QUESTION # 90
Refer to the exhibit.
Refer to the exhibit. An engineer working for a private telecommunication company with an employee id 4115 46 881 is enabling a segment routing solution with these requirements.
A service provider is using the default range for prefix SID.
PE1 must allocate the first SID from the default range for the loopback address PE1 and PE2 loopback SID allocation should have a minimum difference of 500.
Which configuration must be implemented to meet the requirements?
- A. Option D
- B. Option C
- C. Option A
- D. Option B
Answer: D
NEW QUESTION # 91
Refer to the exhibit.
Router 1 has attempted to establish a Cisco MPLS TE tunnel to router 2, but the tunnel has failed. Which statement about this configuration is true?
- A. Router 2 must have a tunnel interface created with router 1 as the destination
- B. Router 1 must define an explicit path to router 2
- C. Router 1 must have Cisco MPLS TE enabled on interface gigabitethernet0/1
- D. Router 1 and router 2 must define the RSVP bandwidth reserved on the physical interfaces
Answer: C
NEW QUESTION # 92 
Refer to the exhibit. R1 is directly connected to R2 and R3. R1 is in BGP AS 123, R2 is in BGP AS 2, and R3 is in BGP AS 3. Assume that there is no connectivity issue between R1, R2 and R1, R3. Which result between BGP peers R1, R2 and R1, R3 is true?
- A. The BGP session comes up between R1 and R2 and between R1 and R3.
- B. The BGP session comes up between R1 and R2, but not between R1 and R3.
- C. The BGP session comes up between R1 and R3, but not between R1 and R2.
- D. The BGP session does not come up between R1 and R2 and between R1 and R3.
Answer: A
NEW QUESTION # 93
Refer to the exhibit. An administrator is troubleshooting Internet access issues on a customer's network. After applying this ISIS configuration to R1, the administrator notices that it fails to redistribute the default route into IS-IS. After checking the connectivity between the ISIS router and the ISP router the engineer confirmed there is Layer 3 connectivity between them. Which action should be taken to correct the problem?
- A. Configure the default route under any routing protocol other than IS-IS
- B. Configure R1 as a Layer 1 router
- C. Add the default-information originate command to the configuration
- D. Associate the default route with a VRF
Answer: C
NEW QUESTION # 94
Drag and drop the features about multicast from the left onto the multicast protocols on the right. Not all options ate used.
Answer:
Explanation:
NEW QUESTION # 95
Refer to the exhibit.
Why is neighbor 10.1.5.5 stuck in "2WAY" state?
- A. OSPF parameters (Area ID or hello interval) are mismatched between R2 and 10.1.5.5
- B. It is an expected behavior when OSPF network type is broadcast
- C. OSPF authentication has failed between R2 and 10.1.5.5
- D. Router ID 10.1.5.5 is not reachable from R2
Answer: B
NEW QUESTION # 96
What is the purpose of ACL type prefix set entries in RPL prefix sets?
- A. They hold IPv4 or IPv6 prefixes that do not match specifications.
- B. They hold IPv4 or IPv6 prefix match specifications.
- C. They hold IPv6 prefix match specifications.
- D. They hold IPv4 prefixes that do not match specifications.
Answer: B
NEW QUESTION # 97
Which command is used to enable BIDIR-PIM under global configuration mode for Cisco IOS XE Software?
- A. Ip pim bidlr-enable
- B. ip pim bidir ip
- C. multicast-routing
- D. ipv4 pim bidir-enable
Answer: A
NEW QUESTION # 98
Refer to the exhibit.
After you applied these configurations to routers R1 and R2, the two devices could not form a neighbor relationship. Which reason for the problem is the most likely?
- A. The two routers have different IS-types.
- B. The two routers have the same area ID.
- C. The two routers have the same network ID.
- D. The two routers cannot authenticate with one another.
Answer: D
NEW QUESTION # 99
Refer to the exhibit.
A network operators configuring BGP PIC on CE1 on already established neighborships with PE1ana PE2 inside the fully converged MPLS network Which element needs to be implemented to make this feature function effectively?
- A. The operator must ensure that all prefixes have the same next-hop from PE1 and PE2 for BGP PICA reserved BGP
- B. community of 1 10 must be used to denote the PIC feature set to the routing protocol
- C. Bidirectional Forwarding Detection must be applied to the upstream facing BGP interfaces.
- D. BGP import export policies must be applied on all devices for the routes needing BGP for PIC
Answer: C
NEW QUESTION # 100
After an engineer configures BGP in R1, it starts receiving this message
*Jun 29 13:30:50.122: %BGP-5-ADJCHANGE: neighbor 192.168.10.1 Down User reset Jun 29 13:30:52.341: %BGP-3-NOTIFICATION: sent to neighbor 192.168.10.1 2/6 (unacceptable hold time) 0 bytes Which action makes the peering come back up again?
- A. Set up a hold-down timer higher.
- B. Make a soft reset to the peer.
- C. Set up a minimum hold-down timer higher.
- D. Set up a hello timer higher.
Answer: C
NEW QUESTION # 101
Which difference must an engineer consider when choosing whether to implement OSPF or IS-IS as the routing protocol on the network?
- A. IS-IS supports ordinary, stub, totally-stub. and NSSA areas, but OSPF supports only stub areas.
- B. To support fast convergence. OSPF uses the LSA arrival timer and IS-IS uses the PRC-interval timer.
- C. The OSPF DR election process is deterministic, and the IS-IS DS election process is not deterministic.
- D. IS-IS links are associated with either a Level 1 area or a Level 2 area at one time, but OSPF links are associated with multiple areas at one time.
Answer: B
NEW QUESTION # 102
Refer to the exhibit.
An engineer is troubleshooting connectivity issues on the MPLS core network. A customer connected through R4 cannot reach the OSPF domain on R5. While checking the routing table of R1, the engineer cannot see all the routes from R3 and R5. Which task must the engineer perform so that R4 is able to reach R5?
- A. Enable route filtering between routers R1 and R3.
- B. Enable OSPF peering and configure route redistribution between routers R4 and R1.
- C. Enable OSPF on the Area-0 routers and configure MP-BGP between routers R1 and R3.
- D. Enable MP-BGP peering on routers R1. R3, R4, and R5.
Answer: B
NEW QUESTION # 103 
Refer to the exhibit. Which statement about this configuration is true?
- A. Router 1 sends up to two paths to neighbor 192.168.1.1 for all routes
- B. Router 1 receives only the best path from neighbor 192.168.1.1
- C. Router 1 receives up to two paths from neighbor 192.168.1.1 for all routes in the same AS
- D. Router 1 sends and receives multiple best paths from neighbor 192.168.1.1
Answer: D
NEW QUESTION # 104
Drag and drop the features from the left into the order of operations for SRv6 SSH field creation and forwarding on the right.
Answer:
Explanation:
NEW QUESTION # 105
Refer to the exhibit.
A network engineer implemented this segment routing configuration. Which statement about the output is true?
- A. The default segment routing global block range is being used on this device.
- B. The device must be reloaded for these ranges to be allocated and used.
- C. A nondefault segment routing global block range is being used on this device.
- D. This range conflicts with the segment routing local block range.
Answer: C
Explanation:
Reference:
segment-routing-book/seg-routing-global-block.html
NEW QUESTION # 106
For which reason can two devices fail to establish an OSPF neighbor relationship?
- A. The two devices have different router IDs
- B. The two devices have the same area ID
- C. The two devices have different network types
- D. The two devices have different process IDs
Answer: C
Explanation:
https://www.cisco.com/c/en/us/support/docs/ip/open-shortest-path-first-ospf/13699-29.html
NEW QUESTION # 107
Refer to the exhibit. Which attribute can router 1 alter so that only other iBGP peers prefer to use
192.168.4.2 as the next hop for route 192.168.3.0/24?
- A. local preference
- B. MED
- C. origin
- D. weight
Answer: B
NEW QUESTION # 108
Which keyword is used with the match route-type command to redistribute the external BGP and IGP routes using route map?
- A. match route-type type-1
- B. match route-type nssa-external
- C. match route-type external
- D. match route-type type-2
Answer: C
NEW QUESTION # 109
Refer to the exhibit.
Why is neighbor 10.1.5.5 stuck in "2WAY" state?
- A. OSPF parameters (Area ID or hello interval) are mismatched between R2 and 10.1.5.5
- B. It is an expected behavior when OSPF network type is broadcast
- C. OSPF authentication has failed between R2 and 10.1.5.5
- D. Router ID 10.1.5.5 is not reachable from R2
Answer: B
NEW QUESTION # 110
......
Cisco 300-510 exam is a 90-minute exam consisting of 60-70 questions. 300-510 exam is available in English and Japanese and can be taken online or at a Pearson VUE testing center. 300-510 exam fee is $300 USD, and candidates are required to renew their certification every three years by passing a recertification exam or earning Continuing Education credits.
Cisco 300-510 certification exam is intended for network engineers, network architects, and network administrators who work in service provider environments. 300-510 exam tests the candidate's knowledge of advanced routing protocols, including OSPF, BGP, and IS-IS, as well as their ability to configure and troubleshoot complex network architectures. In addition to routing protocols, the exam also covers topics such as Quality of Service (QoS), network security, and network automation. Passing 300-510 exam validates the candidate's expertise in service provider routing solutions and enhances their professional reputation in the networking industry.
Free CCNP Service Provider 300-510 Exam Question: https://www.prep4surereview.com/300-510-latest-braindumps.html
Dumps Practice Exam Questions Study Guide for the 300-510 Exam: https://drive.google.com/open?id=1zPBr2kZlLkTYjG2hqxpGVk542rJT98MT
